Leaking pipes can cause a lot of damage to your home if left untreated. There are many temporary fixes for leaking pipes that you can use, such as epoxy putty or pipe clamps, while waiting for a plumber. If you want to fix the pipe yourself so that it is up to the code, you can use a sliding clutch to make the process easy. Whatever you use, be sure to turn off the water supply so that your pipes do not leak while you work!
[ Edit ] Step
[ Edit ] Turn off your water supply
- Turn off the water supply to your home. Find out your main water supply, which is usually located in the basement or crawl space. Turn the knob clockwise to turn off the water entering your home so that the leak stops and causes no more damage. 
- In an emergency, call your water company and see if they can turn off the water leading to your home.
- Turn on the taps connected to the pipe to empty them. Start by turning on the lowest faucet in your home, such as an outdoor hose or basin sink. Let the water run until the pipe is completely empty. If the leak is on a pipe that leads to a specific fixture, then turn on the tap to drop it. 
- Wipe the leaking area of the pipe. When all water has been drained from the pipes, use a cleaning cloth to wipe the area around the leak completely dry. That way it will not be slippery while you try to work on it. 
- Place a cloth or bucket under the leak in case there are any dropped drops of water from the leak.
[ Edit ] Application for Epoxy Putty for a temporary fix
- Put on latex or nitrile gloves. Epoxy putty heats up as you work with it and can cause pain on bare skin. Make sure the gloves are thin enough where you can still work complicated. Wear the gloves when handling epoxy putty. 
- You can buy latex or nitrile gloves from any hardware or large box.
- Mix plumbing epoxy putty by hand to combine it. Draw a small ball of epoxy putty from the tube and knead it together between your fingers. The darker epoxy mixes with the lighter exterior to activate it. When the kit has a uniform light gray color, you can stop kneading it. 
- You can buy plumbing epoxy putty from your local hardware store.
- Take the putty around the leaking area. Shape the kit around the leak on the tube so it wraps completely around it. Make sure the putty forms a layer that is approximately thick around the leak so that it stays in place. Melt the putty on the putty on the tube to make a waterproof seal. 
- Epoxy putty works on straight lengths of pipes and joints.
- Let the kit set for 5-10 minutes before turning on the water. When the epoxy kit is mixed it will be set quickly so you can use your water again. Leave the kitten alone for at least 5 minutes while it sets so it can set. Once the epoxy has been set, you can turn on the water again. 
- Epoxy putty is a temporary fix, so be sure to completely replace the pipe or contact a plumber the next day.
[ Edit ] Clamping Small Leaks
- Buy a pipe clamp that is the same size as the leaking pipe. Pipe clamps use rubber gaskets to create a tight seal to secure a small leak on your pipe. You can buy these in the plumbing section of your local hardware store, but be sure to buy a pipe clamp that is the same size and at least as long as the pipe that leaks so you are stuck when you secure it.  Fix leakage tube Step 8 version 2.jpg "src =" https://www.wikihow.com/imagesorna/8/8a/Fix-Leaking-Pipes-Step-8-Version-2.jpg/aid1787498 -v4-728px-Fix-Leaking-Pipes-Step-8-Version-2.jpg "width =" 728 "height =" 546 "class =" whcdn "/>
[ Edit ] Attach a slide clutch Your Pipe
- Get a slide clutch that matches the pipe size and type. Sliding couplings are small, waterproof connections that connect 2 different pipe pieces. Look for a slide coupling with the same diameter as the pipe you need to fix and long enough to cut the leak. Before you buy one, make sure the coupling is of the same material as your pipe, e.g. PVC or copper.
- You can buy slides from your local hardware store.  Grinding couplings can be a permanent solution to fix your pipes and they are up to the code.
- Select the length of the slide coupling on the pipe. Hold the slide coupling up to the leaking point on the pipe so that the coupling extends from each side. Use a cursor to draw a line on the tube at the end of the slide connector. This helps to ensure that you cut the correct pipe length so that the coupling can still fit. 
- Use a pipe cutter to cut out the leaking area of the pipe. Pipe clippers are small units that easily cut through a pipe as you rotate them around. Place the edge of your pipe cutter inside the line you drew and tighten the screw on the bottom of the unit. Turn the pipe cutter around the pipe completely and tighten the screw again. Continue spinning and tightening the tube cutter until it makes a clean cut through the tube. Repeat the process from the second line you drew. 
- You can buy pipe cutters from your local hardware store.
- Pipe cutters work on metal and PVC pipes.
- Some PVC pipe cutters look like scissors. Place the blade over the tube and slowly push down the blades.
- Scrape the inside and outside of the tube with a drilling tool. A drill bit is a special tool used to scrape the inside and outside of the tube to help reshape it after making your cut. Hold the tube firmly with your non-dominant hand and set the blade edge of the excavator tool inside the tube. Scrape around the inner edge of the tube with your tool to dispose of it. Remove the tool from the tube and scrape the outer edge. 
- You can buy branching tools in the plumbing section of a hardware store.
- Be sure to delimit both sides of the cut pipe to prevent future leakage.
- Slide the slide clutch on the ends of your pipe. Take your clutch and slide one end over one side of the tube. Push the connector long enough so that you can align it with the other side of the cut tube. Align the other end of the connector with the tube and pull it over so that the two tubes are connected by the connector. The coupling holds the pipes together so that water can flow between them. 
- Some connections may cause you to tighten them by hand or with a jerk. Follow the instructions on the package carefully to see if there are any further steps.
[ Edit ] Warnings
- Contact a plumber if you do not feel comfortable cutting or replacing your own pipe or if it is difficult to reach the leak.
[ Edit ] Things You Need
[ Edit ] Applying Epoxy Putty for a Temporal Fix
- Latex or Nitrile Gloves
- Epoxy kit
[ Edit ] Clamping the Leak Shut
- Pipe clamp
- Wrench  [ Edit ] Putting a clutch on your pipe
- Pipe coupling
- Pipe clipper
- Tape measure
- Degradation tool
[ Edit ] Related wikiHows
- Temporarily address a water leak
[ Edit ] Quick Overview
- ↑ https://www.wsscwater.com/customer-service/residential-tips/ locating-and-operating-your-main.html
- [1945 https://youtu.be/u3aeRknUd1U?t= 55
- ↑ https://youtu.be/m3cfvLGiw8E?t= 80  ↑ https://youtu.be/6C9PiaXnuGY?t=54
- ↑ https://youtu.be/6C9PiaXnuGY?t=66ebrit19659087vard↑ https://youtu.be / 6C9PiaXnuGY? T = 87
- ↑ https://youtu.be/6C9PiaXnuGY?t= 127
- [1945 https://youtu.be/m3cfvLGiw8E?t=116
- ↑ https://youtu.be/m3cfvLGiw8E?t=123
- ↑ https: //youtu.be/m3cfvLGiw8E?t=126ebrit19659092strong↑ https://youtu.be/Db_GYaTcrGk t = 235
- ↑ https://youtu.be/Db_GYaTcrGk?t= 235
- ↑ https://youtu.be/Db_GYaTcrGk?t=240
- ↑ https://youtu.be/Db_GYaTcrGk?t=253